What did you build today?

DonM · 2020-01-24T22:58:56+00:00

I'll start. Vertex AW on SK Fiber TT75R shaft. Cleveland Launcher HB 5W on UST 55 Gold R shaft.

DC300

That’s pretty cool, thanks for sharing!

I have a few rounds in with the shafts now and they are nice. I’m thinking I should have tipped them some more though, I have a case of the spins in the Single length irons I built with them. I’m yanking 6irons back, it’s cool and all, but not super helpful for distance 😂. I have been able to flight the shots pretty well and had a lot of “wow” shots with the wedges, those old school Tiger shots, low and hot, 1 hit and zip to a stop. The thing is, I’m not talented enough to actually hit those consistently, so I know I’m getting more spin than I’m accustomed to. My gapping is the real issue, much too tight, full go gets shots spinning too much and dying on me. I think I’ll pull them and take another half inch off.

ThePhillB

LogicalOne NeuroX 5 wood replacing my ol Geek DCT, going back onto the same Grafalloy Epic T75X that has served me well for years. Now I just need to bribe Kelly out of that 4 hybrid head he teased a while back.

Rickochet

darpar Built a couple of darpar designed squatty potty's....

I would call it the Stool stool. 🤣

Will that raise your junk out of the water if you hang a bit too low?

darpar

Rickochet
Be careful, it might put your junk in the trunk!

Typhoon

Bad news was the heat compromised the epoxy on my Ninja LD shaft that I had the Ping G425 LST in. I was at the range and after a shot the head spun around.

Good news is I plan on selling the head, don’t need it and now I don’t have to pull the adapter😂. I’ll clean up the shaft and put a TM on there.

Good warning though, we’ve had a bunch of 90-100 degree days. Clubs were actually in my garage but it’s wicked hot in there… my smoke alarms go off. Taking the clubs inside

Rickochet

Typhoon Good warning though, we’ve had a bunch of 90-100 degree days. Clubs were actually in my garage but it’s wicked hot in there… my smoke alarms go off. Taking the clubs inside

Do you use Bramptons shafting epoxy?

Typhoon

Rickochet No, but I know what you’re saying. A few years back I had Bramptons give out and threw it out. I remember you talking about it at the time.

I use the Golfworks stuff. I’ve been hitting that shaft off and on since the spring without a problem. I would have to blame the heat for the failure.

backinit

Typhoon
I have starting using Bob Smith Industries - BSI-203H. It has a working time of 5 - 10 minutes. Available on eBay and Amazon. Good stuff.

Typhoon

backinit How is it to take apart?

Rickochet

backinit I have starting using Bob Smith Industries - BSI-203H. It has a working time of 5 - 10 minutes. Available on eBay and Amazon. Good stuff.

BSI has good quality stuff but I don't know that I would use that for golf clubs. It looks just like JB Weld. It is almost impossible to pull a shaft from a head that used JB Weld without scorching it. The videos on Amazon show people trying to drill and grind it. Golf shafting epoxy maintains a bit of flexibility for shock absorption. Leave left over glue on a paper plate and after it is dry you can bend the leftover glue. A local dealer used to sell shafting epoxy with his store label on it. He told me he got it from Golfsmith in 5 gallon cans and bottled it with his label. He needed to reorder and GS was out so they had it drop shipped from the mfgr. which was the Hardman Corp.. You can find Hardman Epoweld on ebaybay.

Luc_Van_Daele

The postman brought me some work to do.

sdandrea1

Luc_Van_Daele

Those heads point in different directions. Ambidexterous? Love those i-Drive shafts.

backinit

Typhoon I'll let you know this weekend.

backinit

Rickochet This stuff maintains a very small amount of flexibility after drying. I see that as a good thing. By the looks of things you can play it after about 60 - 90 minutes.
I'll report back after disassembly.

Typhoon

Rickochet t is almost impossible to pull a shaft from a head that used JB Weld without scorching it.

I found that where someone used JB Weld on a putter shaft extension. I had to saw it off 🙄.

backinit

backinit Just an update. I did a pull on a graphite shafted club with Bob Smith's epoxy. It was fairly clean. It might have taken a little more time vs Bramptons. I would say 2 3-4 minute sessions rotating the hosel with the heat gun on high so not terrible at all.

Luc_Van_Daele

sdandrea1 Those heads point in different directions. Ambidexterous?

Tried to fix it for you, but now the print on the I-Drives is all wrong :

What the heck, they're not for myself so I'll send them out to my clients as they are.

Rickochet

Typhoon I found that where someone used JB Weld on a putter shaft extension. I had to saw it off 🙄.

I bought a component fairway wood years ago that needed a reshafting. I almost had to use nuclear weapons to get the glue to release and ended up scorching the crap out of the head. I asked the seller what he used to glue on the head and he told me it was JB Weld. After that I no longer bought a club unless I knew what kind of glue was used.

VigilanteTrail

Demo build night…

Maltby TS3 8 iron with @LogicalOne 85S graphite…tipped per specs

Mated a Cobra adapter with @LogicalOne Leveler…tipped for stiff flex…will cut to 45” and give it a run with LTDx Max 10.5* head

VigilanteTrail

VigilanteTrail Demo build night…

Maltby TS3 8 iron with @LogicalOne 85S graphite…tipped per specs

Typhoon

I was able to successfully push the Ping ferrule off the Ninja shaft and keep it with the adapter. I put the TM adapter on the Ninja shaft. I think is going to be 48.25”😁😁. Fine with me. The shaft with the adapter came out to 47”

ode

Typhoon goodness.....gonna feel like a lumberjack swinging that stick😆

sdandrea1

Typhoon

Can you actually hit a golf ball with a driver that's taller than you? We need a video....

😏😘

Par4QC

Typhoon I think is going to be 48.25”

There really is no need now to ever play a club that long, plus it will 'tell you' nothing about anything. Illegal anyway. Even the LD fellas are using the shorter ones now.
I may sneak an extra 1/4 at times, but now staying at 46 myself. Even trimmed a couple last week for compliance.

I mean, I just don't wanna be 'that guy' that hits the 388 bomb.....then have someone say...'oh sure, with an illegal club'. 🤣

EDIT: Must be behind in times, or didn't read/understand. But, driver length is still 48", for everyone. 46" is a 'local rule' for tournaments. Looks like the LD is still using the longer.

« Previous Page Next Page »