Turning ferrules

sdandrea1 · 2023-03-02T12:10:11+00:00

Can someone give me a primer on turning ferrules? Tricks and tips? Warnings? @scotts33 ? All these years of club building and I've never had to do it unti...

SMT

scotts33 Rotate the shaft the way the belt is turning to remove less material and do a finer job.

If you do that, oftentimes the plastic builds up and you have a big lump.

The belt is always turning down, top to bottom, you should always be going AGAINST that direction. meaning, you should turn the head counterclockwise.

darpar

SMT you should always be going AGAINST that direction. meaning, you should turn the head counterclockwise.

That's the way I've always done it.

scotts33

SMT If you do that, oftentimes the plastic builds up and you have a big lump.

The belt is always turning down, top to bottom, you should always be going AGAINST that direction. meaning, you should turn the head counterclockwise.

That's what I meant Mike I stated it incorrectly. ☺

SMT

Ynotgolf So... Just a ferule on a partial shaft??

How in the heck would you know if you are done or took it down too much?

sdandrea1

CallMeAl Good Job.

Thanks! Yes, now that I have a little experience, I will take the bulge down, if @Bravopilot wants me too. I did not use any tape. The sandpaper was so soft, it had no effect on the hosel, and I stayed away from the shaft.

azgreg

SMT

azgreg If you are planning on using the shoe shine method... Take up bowling.

hahaha

darpar

Ynotgolf Piece of cake.

Not really, doing it the way you described, way too much unnecessary work.

AdamMH

I usually...

Mask the hosel w/ tape
Grab a strip of 220 grit and "shoeshine" the ferrule with it til close to the right diameter
Spin the ferrule on piece of shop towel wet with acetone to get it to final size/sheen

Spuzz

Shine it up with some car wax.

UnholyDefenestrator78

did you account for the change in swingweight pre- and post- turndown?

sdandrea1

UnholyDefenestrator78 did you account for the change in swingweight pre- and post- turndown?

I measured it. Had to add a gnat hair to each head......and they're hard to find since the pandemic.😉

UnholyDefenestrator78

sdandrea1

I stockpiled them, kind of like how others stockpiled Purell and TP

sdandrea1

UnholyDefenestrator78

Wish I'd known......

UnholyDefenestrator78

sdandrea1

you can always use Grogu hairs instead.

mulegolf

I've always used a 1"X30" belt sander. It's like everything you learn. Once you get onto it it's easy. The best
belt I ever found was a linen belt. It turned the ferrule down easily and if you taped the hosel and shaft it
left no marks. I then used strips cut out of Bounty (it had to be Bounty) paper towels soaked with acetone
and spun the club against it. If I was really being picky I'd finish it off with a felt belt and glanz wachs. Sadly,
by the time I quit making clubs I could no longer find either linen belts or felt belts.

LBlack14

I'm damn disappointed in seeing this thread.

ode

Turning ferrules is for squares 😉

Walterjn

Last time I did ferrules,I wrapped a piece of sandpaper around it and spun the shaft using my hand in a rolling motion with the shaft on my leg. Also how I've polished the ferrule with acetone and paper towel.

DonM

sdandrea1
@Mcburbn did a video which has a section on doing with with simple shop supplies.

SMT

DonM Jim is a great guy

FauxAmish

DonM

I remember mcburbn had his daily golf question on the old fgi site. Wish he was still around.

« Previous Page Next Page »