Old Ping Wood Heads to Give Away

kelco9 · 2019-08-30T18:34:47+00:00

I was helping my dad clean out his garage and found these three woods in the corner. I was about to throw them out, but then thought that since there are som...

sdandrea1

Kelco, I'll take them if Tate will pay for the shipping. 😁 I didn't realize you were in Canada.

kelco9

sdandrea1 Yeah, I don't blame you for taking a pass. Shipping across the border can be an expensive affair. It is the reason that I don't buy shafts from the States. The dimension of the box drives the costs up too far. There were some shafts and heads that I was looking at from DTG: shipping to the US, free; shipping to Canada, about $100.

brownmoose13

SMT

Looks like WOW has turned into OOPS!!!

Maybe tait will reply but not before:

He gets his foot out of his mouth
Pulls his head out of his ass and
Crawls out of his hole so he can get a better internet connection so he can reply

He is the perfect example that is better to be thought of as a total jerk than open your mouth and prove it but then again he has years of experience and has it down to perfection.

brownmoose13

tait has logged on here 3 times since my last post. Rather than comment he is probably shaking his piggy bank to raise the $45 to pay for the shipping he promised or maybe he is trying to sell a few of those lifetime warranty golf gloves if any of his lackies that trusted him are left to be found. I apologize I should know better than use the word promise and tait in the same sentence but I am sure he will let us know when he sends the check

sdandrea1

brownmoose13

I thought he was going to pay my shipping. WTF? 😁

cpanther1995

I’m just eating popcorn watching this

garyt1957

cpanther1995 It certainly took an entertaining turn.

sdandrea1

I think SMT is out of this. Chuck for the WIN!

brownmoose13

Maybe, just maybe there is a Postal strike either in the USA or Canada that I not heard about.

bad9

WTF happened here? Obviously there is some “history” I am not aware of.

sdandrea1

bad9

Brownmoose and SMT were both in the golf component business in the past. I think they're paths may have collided.

brownmoose13

sdandrea1

I would like to clarify this before fatboy gets his shorts in a bunch. tait was in the component business and I, as Golfincolors, was in the custom design and refinishing business....I did not sell components. But you are right we did collide in the past and I hope to make it more in person the next time

sdandrea1

brownmoose13

I figured custom refinishing heads as in the business. 😄

brownmoose13

but you forget who I am dealing with an idiot who will make a 3-6 paragraph post detailing his definition of being in the component business and that is after he calls you an idiot for not knowing the definition.
Don't forget I have many years confronting fatboy and I know his tactics

sdandrea1

brownmoose13

He may be right occasionally on the idiot part, but only SWMBO and I are permitted to point that out.

brownmoose13

Must be like Groundhog Day as fatboy came out of his hole earlier today when he logged on
, saw he was getting hammered and must have crawled back in without sending the check. Looks like you are out of luck Steve but on a positive note I hope everyone that has read and kept up on this thread learned a lesson that tait's word has as much value as the center of a donut.

sdandrea1

brownmoose13

Does this mean I'm NOT getting the PING woods? 😞

kelco9

sdandrea1 Well, for what it's worth, I took them out and hit them into my net. All I can say is "We've come a long way, baby."

sdandrea1

kelco9

I know. I have a beautiful PING ZING blonde maple laminated driver with a factory graphite shaft. On center hits, it's actually pretty good, otherwise..........

brownmoose13

Do you think there is a reason that fatboy keeps poking his head out of his hole.....like 2 hours ago....but refuses to tell us when he mailed the check?? If you are reading this tait you can run but not hide unless you are at the PGA Show.

« Previous Page Next Page »