Measuring Club Length

VigilanteTrail · 2024-02-04T05:58:06+00:00

Okay…calling in a favor to all of the experts out there…think I am slowly losing my mind… Ran into a scenario tonight when measuring a club that has made me...

Spuzz

Cutter66 Although I still dont understand how the length of a putter is done

Down the back of the shaft to the ground, NOT to the back of the putter head.
🙂

Cutter66

Spuzz No, no, no! It's way more complicted than that! Some sorta voodoo calculus or something to figure that💩 out!

Or I'm dense, one of the two

Spuzz

Cutter66 Or I'm dense, one of the two

I am reserving comment until I see what shows up in Round 2 of the Buy and Sell
😉

LBlack14

DonM

VigilanteTrail I'd say what you have is correct. We would need a shot of the clubhead from straight overhead of that pencil mark to give any better opinion.

VigilanteTrail

DonM

I will go out and get some better top view pictures 👍

VigilanteTrail

DonM

Don,

I have pretty much convinced myself that my current setup is actually measuring 1/2” short…

…the distance between the edge of sole pin and that line I measured 10” from is exactly 1/2”

I measured two different supposedly “standard” length 7 irons (A PXG 0211DC and a Callaway X-14)…standard length from PXG is 37.5” and the X-14 standard length spec is 37”…but with my setup I got 37” & 36.5” respectively. See below…

DonM

VigilanteTrail
You need to measure to the intersection of the two red lines. And they intersect on your pencil line, so your jig is accurate. Someone correct me if they think otherwise.

azgreg

I just use a block of wood with a 60° angle cut on one side and a 48" ruler.

DonM

But,
If the screw stop was under the center of the sole instead of closer to the heel, you’d have a better measurement, and it would be a longer number. But only another eighth inch?

VigilanteTrail

DonM If the screw stop was under the center of the sole instead of closer to the heel, you’d have a better measurement

This right here ☝️

I just made some adjustments to my jig pins so that the sole contacts the pin at the center of sole and now everything seems to be measuring right…the X-14 is measuring 37” and I measured my Exotics E722 #2 hybrid which is standard length at 40.75” and that is the measurement I got as well.

Many thanks for your input & advice @DonM

pellmell

Cutter66 Although I still dont understand how the length of a putter is done

There's no standard for putter length measurement. Next time you're at a golf retailer grab three putters with the same stated length from different companies and set them down in the playing position, you'll see they don't match. To be consistent regardless of head design, I measure from the site line/dot, which is typically the center of the clubface, to the grip endcap.

Spuzz

pellmell There's no standard for putter length measurement.

Yes there is. It's in the rules of golf.
18 inches minimum length, measured down the shaft to the sole/ground., as I said.
If you mean no standard for how the OEM's measure their own stuff and label it, then I agree.

LBlack14

🤣

scotts33

I'll just throw this out there as the lie angle changes the playing length changes. ☺

MidwayJ

sdandrea1 I've been using a measuring tape down the shaft to the floor with the club in playing position for decades. I always have an OEM club sitting around for a comparison check.

That's the method that measures 1/4 to 1/8 inch short according to the graphic. Is that what you find when comparing to the OEM club.

sdandrea1

MidwayJ That's the method that measures 1/4 to 1/8 inch short according to the graphic. Is that what you find when comparing to the OEM club.

I usually get 1/8" short using that and after I put the grip on, I'm right on standard.

KCee

I never understood why I need to use one method/fixture to measure irons and woods and another method to measure the putter. I remember years ago placing my new off the rack putter on my new aluminum measuring ruler from Golfsmith and thinking "why is my 35" putter not measuring 35....all my other clubs measured perfectly wtf?". Another conspiracy.

LBlack14

KCee 🤣

KCee

LBlack14 I know right LOL.

Seriously though when I started building clubs I think I did a driver first and then a set of irons and so on. I probably built a bunch of clubs before I built a putter and when I did I wondered if I had built ANYTHING to the correct length lol.